Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
Each person seems to have their own individual idea when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a new one is also a moderately hard task. If the old tub is readily accessible, the task can relocate quickly; if you have to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work as well as are comfortable trying it. Instead of employing a professional to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you set up a new tub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the plan of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washers are in place between the tap and the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wood boards under its feet, put the bathtub in the called for placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
To install taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system as well as check all joints and also new pipework for leakages as well as tighten them if required. Load the tub as well as likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of once as this will resolve it into its last position.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in problems with moisture and also feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I stumbled upon that blog post about How to Install a Bathtub Yourself while doing a lookup on the web. Sharing is nice. You just don't know, you could be doing someone a favor. We value reading our article about Tools You Need to Install a New Bathtub .
Explore Now Report this page